OPERATION
1
Squeeze operating lever completely.
2
Release operating lever completely.
3
Apply label to item being marked as shown.
Rollers
A wiping motion works best, DO NOT POUND
n
labeler when applying labels.
REMOVING SUPPLIES
1
2
Tear label strip and carefully remove label roll.
Squeeze and release operating lever until
backing paper exits here.
Tear
MAINTENANCE
1
2
If labeler has no label guide:
If labeler has label guide:
To clear backing paper
Remove label roll. Squeeze
Remove label roll. Squeeze
track, insert label removal
operating lever half way and feed label
operating lever half way and feed
strip here, using corner to
removal strip under brake wheels . . .
label removal strip over label guide,
remove stray labels.
under brake wheels . . .
Label
Guide
Insert label removal strip here
and out the front of labeler.
and out the front of labeler.
to loosen labels.
3
4
Squeeze operating lever to turn feedwheel
Remove ink door and inspect door opening for
for inspection. Remove stray labels with corner
stray labels. Remove stray labels with corner of
of label removal strip.
label removal strip.
Feedwheel
OPERATION, REMOVING SUPPLIES & MAINTENANCE
LUBRICATION
TROUBLESHOOTING
Problem
Solution
Monarch Lubricant 086989 is recommended.
Lubricate as shown below with labeler loaded
Labels will not
Reload per instructions.
when:
feed.
Check for correct supplies.
a.
slow or hesitant feeding occurs.
Follow MAINTENANCE
b.
adhesive buildup is seen.
instructions.
c.
feedwheel tears backing paper.
d.
ink roll is changed.
Check for correct print location.
LUBRICATE:
Print incorrectly
Adjust per PRINT LOCATION
One drop
located.
ADJUSTMENT instructions.
each side of
Printing smeared
Print several labels (15-20) until
label chute.
or distorted.
excess ink is used up.
Printing too light
Install new ink roll per INKING
LUBRICATE:
(all over).
instructions.
One drop each spot on
backing paper. Spread
Squeeze operating lever harder
with finger.
during operation.
Slow hesitant
Follow MAINTENANCE
feeding. Labeler
instructions.
tends to `hang up'
Lubricate per instructions.
when operating
lever is released.
DO
NOT OVER
If none of the above eliminates the problem, return
LUBRICATE!
labeler to an Authorized Monarch Service Center.
PRINT LOCATION ADJUSTMENT
AVAILABLE SUPPLIES
CCH-15
Case Cutter Holder
Print location is correct when
HB-10
Holster (Vinyl)
all characters are fully visible on
089768
Label Removal Strip
PRY-1
Label Scraper (w/ handle)
the printed label. Dial characters
SLS-1
Label Scraper (w/o handle)
for every position when testing
096335-M10
Maintenance Kit
location.
083946-05
Purple Ink Roll
086989
Silicone Lubricant
(1/2 oz.) (15 ml.)
1
Place small coin in slot of each
088992
Wrist Strap
disk (one on each side of labeler)
as shown.
2
Hold coin steady in slot labeled
HOLD, and turn other coin very
slowly clockwise until one click is heard.
3
Print sample label and check for
correct print location.
4
Repeat steps 1, 2, and 3 until print
is correctly located. If correct print
location is passed, continue adjustment
until correct print location reappears.
For supplies, service, or assistance call:
Warranties
TOLL FREE:
PRODUCT WARRANTY STATEMENTS MAY VARY
1-800-543-6650 (In the U.S.A.)
FROM COUNTRY TO COUNTRY
.
PLEASE CONTACT THE AUTHORIZED PAXAR
1-800-263-4650 (In Canada)
REPRESENTATIVE IN YOUR COUNTRY
Internet Address:
FOR DETAILS.
www.monarch.com
LUBRICATION, TROUBLESHOOTING, PRINT LOCATION & SUPPLIES
TC1000OI Rev DB 02/02
Back
to StoreSupplies.com 
Main Questions and
Answers
Back Page
